•  

MPCADE24-ICT

MedMaster for Patient Rooms

MPCADE24-ICT Main Image
MPCADE24-ICT Main Image
Model #: MPCADE24-ICT
Features:
  • Ambient and exam lighting with optional reading compartment
  • Ambient function provides environmental disinfection and effective, efficient lighting performance via visible LED light
  • Dual-Mode Indigo-Clean Technology is independently tested to kill 94% of SARS CoV-2 and Influenza-A***, in addition to MRSA
  • Single-Mode Indigo-Clean Technology is independently tested to kill harmful bacteria, such as Staph*, including MRSA**
  • Ingress Barrier Door provides consistent surface for cleanability
Application(s):Patient Rooms
Isolation Areas
Lamp Type(s):LED
Size(s):24"×48"
Listings:    
Specifications are subject to change without notice. Please consult your Kenall Customer Service for help with special requests at (800) 4 Kenall.

Technical Specifications

DoorframeHeavy duty extruded aluminum with clear satin anodized finish. Doorframe supported to housing with aircraft cables (IB-AC) to provide NSF2 listing, or an optional continuous hinged doorframe (IB-HD). Select in ordering options below. Phillips-head stainless steel fasteners secure door to housing – 8 with IB-AC  and 2 with IB-HD. Extruded closed cell gasket seals doorframe to housing.
Electrical
 120-277VAC and 347VAC electrical input with serviceable high power factor electronic, constant-current drivers (<10% THD, >0.90 PF). Minimum 85% driver efficiency. Standard 0-10V dimming with 1-100% range and dim-to-dark capabilities. 330μA maximum source current.  Exam Function includes serviceable standard mid-power white LED array (non-disinfection). Available 3500K, 4000K and 5000K color temperature, minimum 82 CRI standard.  Ambient Function with Single- and Dual-Mode ICT includes serviceable mid-power white and 405nm Indigo LED array. Available 3200K, 3700K and 4300K color temperatures with 3-step MacAdam variation allowance. Minimum 82 CRI standard. Single-Mode ICT provides a single, white disinfection operational mode.  Dual-Mode ICT provides two operational modes based on room occupancy.  White Disinfection Mode is a white LED array for ambient lighting plus a simultaneous low-power 405nm LED array for low-level, continuous and safe environmental disinfection.  Indigo Disinfection Mode is a higher-level 405nm array for continuous safe environmental disinfection during periods of room vacancy.  The operational mode is determined via internal low-voltage device based upon the input signal provided by an external control device/system.  Luminaire dimming is overridden in this operational state.  Refer to the Kenall Dual-Mode ICT Control Application Guide for further description. 
HousingFLANGE AND GRID: 20-gauge CRS seam welded one-piece construction. SURFACE: 18-gauge CRS one-piece seam welded construction. White TGIC polyester powder coast – 5-stage pre-treatment. Salt spray test 1,000 hours. Reflectance 92%. (See options for Antimicrobial Finish). Housing Flanges –18-gauge CRS.
InstallationGrid Mount: Designed for 1" and 1.5" grid. (Housing includes hanging brackets to secure housing with wire to super structure). Flange Mount: Yoke mounting hardware & brackets included. Install Frame and Plaster Frames both positively locates yoke brackets within ceiling opening assures alignment of fixture. Install frame has no need for drywall backing. Backing is supplied on the frame brackets.
Lamp ShieldingExam compartment shielded by frosted linear prismatic high impact acrylic. Ambient compartment shielded by 100% internal fluted high impact acrylic.
Lens .125" clear high impact acrylic. Sealed to extruded aluminum frame with a vinyl gasket.
ListingsUL and CUL Listed for Wet Location and UL certified IP65 per IEC 60598. NSF2 Splash/Non-Food Zone (IB-AC only). CCEA approved for grid or flange mount.
WarrantyLimited five (5) year warranty on LED lamps.

This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin.

Downloads

Product Documentation

Installation Files

Photometry (IES)

Additional Resources

 

Challenging Lighting Applications... Demand Kenall

START A CONVERSATION

For product information or layout assistance, connecting with us is easy:

  LOOKING FOR PRICING?
Find a Rep

map marker icon

Search

Helpful Links

Buy American Act Compliant
Unless otherwise noted, our products comply with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin.

 

A Brand of Legrand

© 2017 Kenall Manufacturing. All Rights Reserved.

This site is powered by the Northwoods Titan Content Management System.

top